Request Information Download PDF Configure Output Connector
GT-91128LIXCEL, ITE Power Supply, Wall Plug-in, Li-Ion Battery Charger, , Input Rating: 100-240V~, 50-60 Hz, NEMA 1-15P, North America Blades, Class II 2 Conductors, Output Rating: 4.2 Watts, Power rating with convection cooling (W) , 4.2V in 0.1V increments, Approvals: ETL; CB 60335; GT-91128LIXCEL
Information
Model NumberGT-91128LIXCEL
DescriptionGT-91128LIXCEL, ITE Power Supply, Wall Plug-in, Li-Ion Battery Charger, , Input Rating: 100-240V~, 50-60 Hz, NEMA 1-15P, North America Blades, Class II 2 Conductors, Output Rating: 4.2 Watts, Power rating with convection cooling (W) , 4.2V in 0.1V increments, Approvals: ETL; CB 60335;
Agency Documents
CE EC-Declaration for MedicalContact GlobTek for more information
CE EC-Declaration for Industrial/Commercial/ITEhttps://globtek.secure.force.com/models/ec_declaration?id=a0Oa000000MmNnVEAV
CE EC-Declaration for HouseholdContact GlobTek for more information
RoHS/RoHS3 Declarationhttps://www.globtek.com/pdf/rohs_cert/a0Oa000000MmNnVEAV
REACH Declarationhttps://www.globtek.com/pdf/iso_certificates/REACH.pdf
Conflict Minerals Declarationhttps://www.globtek.com/pdf/conflict-minerals.pdf
Model Parameters
TypeWall Plug-in / Steckergerät
TechnologyLi-Ion Battery Charger
CategoryITE Power Supply / Netzgerät ITE
Input Voltage Range (V)100-240V~, 50-60 Hz
Max Input Current (A)2A
Max Output Power Rating (W)4.2
Output Voltage Range (V)4.2
EfficiencyN/A
Ingress ProtectionIndoor Use
Size (mm)60*65*26
EnclosureUser-added image
 
Rating Table
Model Number (Final ordering #/Part No to be defined) VoltageAmps (A)Watts (W) RFQ
GT-91128LI1CEL* 4.214.2
GT-91128LI1CEL* 8.41.210.08
* (Final ordering #/Part No to be defined)
SpecificationsA) ELECTRICAL SPECIFICATIONS per each channel:
Input Voltage: Specified 90-264 Vac, Nameplate rated: 100-240Vac
Input Frequency: Specified 47-63 Hz, Nameplate rated 50-60Hz
Input Current: < 2A RMS Max
01. Charging Voltage: 1 cell: 4.2Vdc, +/-1% Maximum; 2 cell: 8.4Vdc, +/-1% Maximum; 3 cell: 12.6Vdc, +/-1% Maximum
02. Pre-Charge Current: 10% of bulk charge current
03. Bulk Charge Current: ±10%
04. Pre-Charge to Bulk Charge Battery
05. Transition Voltage: 1 cell: 2.86Vdc to 3.15Vdc, 2 cell: 5.72Vdc to 6.30Vdc; 3 cell: 8.58Vdc to 9.45Vdc Charger will be in pre-charge mode when the battery voltage is below the transition voltage.
06. Battery Charging Ambient Temperature: 0°C to 35°C
07. Charge Termination Current: 10% of bulk charge current
08. Back-Up Charge Termination: Timer set 2 to 3 hours after the expected full charge time
09. Charger will terminate charging when timer expired
10. Battery Protection
11. LED Charge Status Indicator
a. Pre-Charge: Solid Red
b. Bulk Charge: Solid Red
c. Charge Complete: Solid Green
d. No battery or Fault: Green and Red LED off


B) PROTECTION*
01. Over Voltage Protection: 1 cell: 4.6Vdc - 5.0Vdc, 2 cell: 9.2Vdc - 10.0Vdc; 3 cell: 9.2Vdc - 10.0Vdc Charger will terminate charging when over voltage occurs
02. Short Circuit Protection: Charger will not commence charging when BAT+ and BAT- are shorted
03. Reverse Battery Protection: Battery should be mechanically protected from being installed reversed
04. Defective Battery Protection: If battery voltage will not rise above the pre-charge to bulk charge transition voltage (2.86Vdc to 3.15Vdc) within 30 minutes from the time pre-charging begins, the battery is considered defective and the charger will terminate charging.

*When fault condition occurs, the battery has to be removed from the charger and reinstalled after at least 3 seconds to reset the protection. Charging will commence after battery reinstallation only when the fault is cleared.

C) SAFETY
1. Dielectric Withstand Voltage: 4242 Vdc from primary to secondary
2. Earth Leakage Current: N/A for Class II units, there is no PE Ground pin, so Earth Leakage current is not measured
3. Touch Current: Maximum allowed values: 100uA NC(Normal condition) 500uA SFC(single fault condition)


D) OTHER:
01. MTBF: 200,000 Hours @ 25°C ambient temperature
02. Operating Temperature: 0°C to 35°C ambient temperature
03. Humidity: 0% to 90% relative humidity
04. Storage Temperature: -10°C to 70°C
05. Cooling: Convection

E) ENCLOSURE
01. Housing: High impact plastic, 94V0 polycarbonate, non-vented
02. Size: 60*65*26 +/-1.0 mm
03. Markings: Label and/or Pad Printed and/or Molded in the case
Derating CurveN/A
Qty (ea.)/Carton60
Individual Box/Gift Box Size (mm)142*60*62
Individual Box/Gift Box ColorWhite
Master Carton Size (mm)442 x 330 x 275
Gross Weight (kg)15.2
Label Width (mm)45.0
Label Height (mm)50.0
Input Configuration
DescriptionNEMA 1-15P, North America Blades, Class II 2 ConductorsAll NEMA 1 devices are two-wire non-grounding devices (hot-neutral) rated for 125 V maximum. NEMA 1-15P plugs have two parallel flat blades, 0.25 inches (6.35 mm) wide, 0.06 inches (1.524 mm) thick, 0.625-0.718 inches (15.875–18.256 mm) long, and spaced 0.5 inches (12.7 mm) apart.
Output Configuration
Common output connector options:
Click to add to your request.
L Type (Coaxial 5.5x2.5mm plug)
C Type (Coaxial 5.5x2.1mm plug)
K Type (Coaxial 3.5x1.3mm plug)
LL Type (5.5x2.5mm Locking 760k type)
CL Type (5.5x2.1mm Locking S761k type)
Magnetic Connector
L Type (Coaxial 5.5x2.5mm plug) C Type (Coaxial 5.5x2.1mm plug) K Type (Coaxial 3.5x1.3mm plug) LL Type (5.5x2.5mm Locking 760k type) CL Type (5.5x2.1mm Locking S761k type) Magnetic Connector
YL3 Type (KPPX-3P)
YL4 Type (KPPX-4P)
EJ1/2/3/4/5 (EIAJ RC-5320A type connectors)
MSB Type (Micro USB)
Custom design
YL3 Type (KPPX-3P) YL4 Type (KPPX-4P) EJ1/2/3/4/5 (EIAJ RC-5320A type connectors) MSB Type (Micro USB) Inquire for custom design

For a comprehensive list of options, click here

Contact GlobTek for your specific requirements or custom solutions.

Approvals
LogoDescription

No Logo Applicable

IEC 60335-1:2010 (Fifth Edition) incl. Corr. 1:2010 and Corr. 2:2011 + A1:2013
User-added imageIEC 60601-1-11 Issued: 2015/01/20 Ed. 2 Medical Elec. Equip.- Part 1-11: Gen. Req. for Basic Safety &Essential Perf.- Collateral Standard - Req. for Medical Elec. Equip. & Medical Elec.Systems Used in the Home Healthcare Environment
Popular Products (Stock items)
SKUVolts OutCurrent Out (Amps)ConnectorRFQSample Request
2286054.21.0Micro USB type B without resistor

Information anfordern

Call
Email
💬
Text
💁
Chat
?
Request a Quote